You need to design a traffic light controller for an intersection between a Main Road and a Side… 1 answer below »
Traffic Light Controller
You need to design a traffic light controller for an intersection between a Main Road and a Side
Street shown in the figure below. Both the Main Road and Side Street have a red, yellow, and
green signal light. The Main Road typically carries more traffic than the side street, but at peak
times the side street has enough traffic that the traffic lights must adjust their timing.
The traffic light controller works as follows:
1. The traffic light usessensors at the intersection of the Side Street (ST) with the Main Road
(MD) to sense the presence of cars.
2. The traffic light controller makes use of three timers: a 60 seconds timer (T60), a 30
seconds timer (T30), and a 10 seconds timer (T10). Once a trigger signal is applied to a
timer, the timer output is zero and becomes 1 after the programmed time period. For
example, upon reset, the T30 timer output is ‘0’ and will become ‘1’ after 30s have elapsed
and stays ‘1’ until reset by the controller.
3. Pedestrians can use the intersection by pressing buttons. Pedestrians will need to cross
MD only since crossing the side road is assured most of the time.
4. MD lights remain green as long as there are no cars triggering the ST sensors or
pedestrians the crossing button.
5. When MD lights have been green for a minimum of 60 seconds, a car on ST may cause
MD lights to cycle through yellow to red states.
6. Meanwhile, ST lights will turn green and remain green for a minimum of 30 seconds.
Further application of ST sensors within the 30 seconds will enable ST to remain green for
a maximum of 60 seconds.
7. ST lights will cycle through yellow and red states and MD lights will then turn green.
8. The lights stay yellow for 10 seconds.
9. In the default state, MD lights show GREEN and ST lights show RED.
SCHOOL OF ELECTRICAL ENGINEERING & TELECOMMUNICATIONS ELEC2141 – DIGITAL CIRCUIT DESIGN ASSIGNMENT 2 th DUE DATE: 30 April 2019, 11:55 PM Your assignment solutions are to be submitted in pdf format on Moodle. Combine all scanned copies of your handwritten work and electronic documents into one pdf file for the submission. In your submission file include a scanned copy of a completed and signed assignment submission form as the front page. Use Xilinx ISE (or any other appropriate CAD tool) to simulate and verify your design. Attach all design and simulation materials such as schematics, HDL code, simulation outputs and testing fixtures.Traffic Light Controller You need to design a traffic light controller for an intersection between a Main Road and a Side Street shown in the figure below. Both the Main Road and Side Street have a red, yellow, and green signal light. The Main Road typically carries more traffic than the side street, but at peak times the side street has enough traffic that the traffic lights must adjust their timing. The traffic light controller works as follows: 1. The traffic light uses sensors at the intersection of the Side Street (ST) with the Main Road (MD) to sense the presence of cars. 2. The traffic light controller makes use of three timers: a 60 seconds timer (T60), a 30 seconds timer (T30), and a 10 seconds timer (T10). Once a trigger signal is applied to a timer, the timer output is zero and becomes 1 after the programmed time period. For example, upon reset, the T30 timer output is ‘0’ and will become ‘1’ after 30s have elapsed and stays ‘1’ until reset by the controller. 3. Pedestrians can use the intersection by pressing buttons. Pedestrians will need to cross MD only since crossing the side road is assured most of the time. 4. MD lights remain green as long as there are no cars triggering the ST sensors or pedestrians the crossing button. 5. When MD lights have been green for a minimum of 60…
Attachments:
Assignment-2-….pdfDo you need a similar assignment done for you from scratch? We have qualified writers to help you. We assure you an A+ quality paper that is free from plagiarism. Order now for an Amazing Discount!
Use Discount Code "Newclient" for a 15% Discount!
NB: We do not resell papers. Upon ordering, we do an original paper exclusively for you.
